Plastic waste management in recycling facilities: Intentionally generated MPs as an emerging contaminant.

There is little knowledge about microplastic (MP) pollution in plastic recycling facility (PRF) wastewater. In this study, MPs in the wastewaters of four PRFs located in Türkiye were characterized for size, shape, color, and polymer types after sieving from 5,000 µm to the lowest 75 µm with seven sieves. The wet peroxide oxidation procedure was applied before attenuated total reflectance fourier transform infrared spectroscopy analysis for polymer identification. Polyethylene, and polypropylene were the dominant (75 % of total count) MP types within 22 polymer types. Average hit qualities of polymers increased from 69 % to above 84 % for the device software (OPUS) and open software (OpenSpecy). The abundance of MPs was determined as 53,987 MPs/L and 0.8 g MP/L for mixed PRFs 7,582 MPs/L and 4.6 g/L for the LDPE recycling facility, and 2,196 MPs/L and 0.06 g MPs/L for the granulation cooling water by count and weight, respectively. Small-sized MPs are found in the bottom sample much more than the surface and effluent samples in the washing tank. This indicated that MPs adsorbed the pollutants settled in the washing tank due to adsorbed pollution/biofilm. A maximum of 4.6 kg MP/ton of plastic recycled can be discharged as MPs that can be recovered. Considering the plastics recycling capacity, discharged MPs in these PRFs are possibly above 30,000 tons.

Study on green closed-loop regeneration of waste lithium iron phosphate based on oxalic acid system.

The recovery of valuable metals from used lithium batteries is essential from an environmental and resource management standpoint. However, the most widely used acid leaching method causes significant ecological harm. Here, we proposed a method of recovering Li and Fe selectively from used lithium iron phosphate batteries by using low-concentration organic acid and completing the closed-loop regeneration. Low-concentration oxalic acid is used to carry out PO43-, which is significantly less soluble in aqueous solution than Li, two-stage selective leaching Li, where the leaching rate of Li reaches 99 %, and the leaching rate of Fe is only 2.4 %. The leach solution is then decontaminated. The solubility of Li3PO4 in aqueous solution is much smaller than that of Li2C2O4, which was required to recover Li to change the pH and Li can be recovered as Li3PO4; Fe can be retrieved as FeC2O4·2H2O, and re-prepared into lithium iron phosphate.

LCA of recycling aluminium incineration bottom ash, dross and shavings in a rotary furnace and environmental benefits of salt-slag valorisation.

Recycling aluminium in a rotary furnace with salt-fluxes allows recovering valuable alloys from hard-to-recycle waste/side-streams such as packaging, dross and incinerator bottom ash. However, this recycling route generates large amounts of salt-slag/salt-cake hazardous wastes which can pose critical environmental risks if landfilled. To tackle this issue, the metallurgical industry has developed processes to valorise the salt-slag residues into recyclable salts and aluminium concentrates, while producing by-products such as ammonium sulphate and non-metallic compounds (NMCs), with applications in the construction or chemical industries. This study aims to assess through LCA the environmental impacts of recycling aluminium in rotary furnaces for both salt-slag management routes: valorisation or landfill. It was found that this recycling process brings forth considerable net environmental profits, which increase for all the considered impact categories if the salt-slag is valorised. The main benefits arise from the production of secondary cast aluminium alloys, which is not unexpected due to the high energy intensity of aluminium primary production. However, the LCA results also identify other hotspots which play a significant role, and which should be considered for the optimisation of the process based on its environmental performance, such as the production of by-products, the consumption of energy/fuels and the avoidance of landfilling waste. Additionally, the assessment shows that the indicators for mineral resource scarcity, human carcinogenic toxicity and terrestrial ecotoxicity are particularly benefited by the salt-slag valorisation. Finally, a sensitivity analysis illustrates the criticality of the metal yield assumptions when calculating the global warming potential of aluminium recycling routes.

Process and systematic study of gold recovery from flexible printed circuit boards (FPCBs) using a choline chloride-ethylene glycol system.

The traditional hydrometallurgy technology has been widely used to recover precious metals from electronic waste. However, such aqueous recycling systems often employ toxic/harsh chemicals, which may cause serious environmental problems. Herein, an efficient and environment-friendly method using a deep eutectic solvent (DES) mixed system of choline chloride-ethylene glycol-CuCl2·2H2O is developed for gold (Au) recovery from flexible printed circuit boards (FPCBs). The Au leaching and precipitation efficiency can reach approximately 100 % and 95.3 %, respectively, under optimized conditions. Kinetic results show that the Au leaching process follows a nucleation model, which is controlled by chemical surface reactions with an apparent activation energy of 80.29 kJ/mol. The present recycling system has a much higher selectivity for Au than for other base metals; the two-step recovery rate of Au can reach over 95 %, whereas those of copper and nickel are < 2 %. Hydrogen nuclear magnetic resonance spectroscopy (HNMR) and density functional theory (DFT) analyses confirm the formation of intermolecular hydrogen bonds in the DES mixed system, which increase the system melting and boiling points and facilitate the Au leaching process. The Au leaching system can be reused for several times, with the leaching efficiency remaining > 97 % after five cycles. Moreover, ethylene glycol (EG) and choline chloride (ChCl) act as aprotic solvents as well as coordinate with metals, decreasing the redox potential to shift the equilibrium to the leaching side. Overall, this research provides a theoretical and a practical basis for the recovery of metals from FPCBs.

Coupling redox flow desalination with lithium recovery from spent lithium-ion batteries.

Electrochemical redox flow desalination is an emerging method to obtain freshwater; however, the costly requirement for continuously supplying and regenerating redox species limits their practical applications. Recycling of spent lithium-ion batteries is a growing challenge for their sustainable utilization. Existing battery recycling methods often involve massive secondary pollution. Here, we demonstrate a redox flow system to couple redox flow desalination with lithium recovery from spent lithium-ion batteries. The spontaneous reaction between a battery cathode material (LiFePO4) and ferricyanide enables the continuous regeneration of the redox species required for desalination. Several critical operating parameters are optimized, including current density, the concentrations of redox species, salt concentrations of brine, and the amounts of added LiFePO4. With the addition of 0.5920 g of spent LiFePO4 in five consecutive batches, the system can operate over 24 h, achieving 70.46 % lithium recovery in the form of LiCl aqueous solution at the concentration of 6.716 g·L-1. Simultaneously, the brine (25 mL, 10000 ppm NaCl) was desalinated to freshwater. Detailed cost analysis shows that this redox flow system could generate a revenue of ¥ 13.66 per kg of processed spent lithium-ion batteries with low energy consumption (0.77 MJ kg-1) and few greenhouse gas emissions indicating excellent economic and environmental benefits over existing lithium-ion battery recycling technologies, such as pyrometallurgical and hydrometallurgical methods. This work opens a new approach to holistically addressing water and energy challenges to achieve sustainable development.

Surgical instrument wrap: a pilot recycling initiative.

BACKGROUND: Seven per cent of general waste and 20% of healthcare risk waste produced in acute hospitals in Ireland comes from operating theatres. Surgical wrap comprises 11% of operating theatre waste. AIMS: The primary aim of this study was to pilot the implementation of a recycling initiative for surgical instrument set wrap in an operating theatre in Ireland. Secondary aims included quantification of the surgical wrap diverted from general waste to recycling streams over a 5-week period and estimation of the annual carbon emissions associated with gynaecology surgical wrap use in Cork. METHODS: The amount of polypropylene surgical wrap generated by a single gynaecology theatre at Cork University Maternity Hospital was prospectively quantified from 24/1/22 to 1/3/22. At the end of the study period, individual sheets of polypropylene wrap were counted and dimensions were measured to calculate the total surface area of surgical wrap saved for recycling. RESULTS: A total of 66 surgeries were performed over the 5-week study period. Two hundred twenty-one individual sheets of surgical wrap were collected, equating to 282.1 m2 of polypropylene wrap. An estimated 11,564 m2 of surgical wrap could be recycled annually from the gynaecology theatre service in Cork with an associated annual carbon emissions equivalent of at least 2.2 tonnes of CO2. CONCLUSION: Diversion of surgical wrap from general waste and clinical waste streams to the recycling stream is achievable in every operating theatre. Small changes to operating theatre waste disposal practices have the potential to yield significant reductions to theatre waste outputs and to hospital carbon emissions.

Eco-friendly approach for enhancing the floatability of non-metallic components in waste printed circuit boards: Adding gutter oil during dry grinding.

Waste printed circuit boards (WPCBs) are an attractive secondary resource that is challenging to dispose of due to its complexity. Reverse flotation is an effective method to remove non-metallic particles (NMPs) to obtain metals from WPCBs. Nevertheless, the removal of NMPs is usually inadequate in the present flotation practice. Thus, to provide a clean approach to improve the removal efficiency of NMPs, the method of adding gutter oil during dry grinding process was adopted to enhance the hydrophobic sites on the surface of NMPs to improve the floatability. The surface morphology of NMPs was analyzed by SEM, the results show that the rough morphology inhibited the adhesion of bubbles, while water occupied the cracks and pores, making it challenging for collector adsorption, which result in unstable particle-bubble adhesion. The results of FTIR indicate that both NMPs and gutter oil have -CH3, -CH2, -C = O, -C-O functional groups, which promotes the adsorption of gutter oil on the surface of NMPs. The contact angle (CA) results show that the adsorption of gutter oil on the particle surface is conducive to the formation of enhanced CA. Furthermore, the flotation enhancement effect was verified by flotation kinetic experiments. The accumulated floats yield of NMPs conditioned by gutter oil during grinding is increased from 67.05% (NMPs without conditioning) to 95.02%, and the resin recovery is increased by 31.10%. It is demonstrated that dry grinding with gutter oil can strengthen the floatability of NMPs, which provides a potential approach to increase the flotation efficiency of WPCBs.

Experimental study of bifacial photovoltaic module with waste polyvinyl chloride flex and acrylonitrile butadiene styrene road side safety sticker as an alternative reflector: optimization using response surface methodology.

Bifacial photovoltaics (PV) are gaining rapid attention and their ability to generate more electricity is accelerating their deployment globally. However, literature on optimal bifacial PV is presented for the installation parameters of the system. In this study, we use response surface methodology (RSM) to investigate the flex and roadside reflector wastes as alternate reflectors for bifacial PV modules by using a statistical model. Our primary objective in this study is to examine the significant influence of key input factors (front irradiation, rear irradiation, temperature, thickness, and height) on the irradiance factor, total solar reflectance, and power extracted. The results show that the power extraction of the bifacial PV module using the waste flex material is 9%, higher than that of the road side sticker waste. The result indicates that among all other input factors, front irradiation is the most significant parameter.

Environment-friendly, efficient process for mechanical recovery of waste lithium iron phosphate batteries.

Technology for recycling retired lithium batteries has become increasingly environment-friendly and efficient. In traditional recovery methods, pyrometallurgy or hydrometallurgy is often used as an auxiliary treatment method, which results in secondary pollution and increases the cost of harmless treatment. In this article, a new method for combined mechanical recycling of waste lithium iron phosphate (LFP) batteries is proposed to realize the classification and recycling of materials. Appearance inspections and performance tests were conducted on 1000 retired LFP batteries. After discharging and disassembling the defective batteries, the physical structure of the cathode binder was destroyed under ball-milling cycle stress, and the electrode material and metal foil were separated using ultrasonic cleaning technology. After treating the anode sheet with 100 W of ultrasonic power for 2 minutes, the anode material was completely stripped from the copper foil, and no cross-contamination between the copper foil and graphite was observed. After the cathode plate was ball-milled for 60 seconds with an abrasive particle size of 20 mm and then ultrasonically treated for 20 minutes with a power of 300 W, the stripping rate of the cathode material reached 99.0%, and the purities of the aluminium foil and LFP reached 100% and 98.1%, respectively.

Selective leaching process for efficient and rapid recycling of spent lithium iron phosphate batteries.

With the continuous development of new energy vehicles, the number of decommissioned lithium iron phosphate (LiFePO4) batteries has been constantly increasing. Therefore, it is necessary to recover metal from spent LiFePO4 batteries due to the high potential for environmental protection and high resource value. In this study, sodium persulfate (Na2S2O8) was selected as the oxidant to regulate and control the oxidation state and proton activity of the leaching solution through its high oxidizing ability. Selective recovery of lithium from LiFePO4 batteries was achieved by oxidizing LiFePO4 to iron phosphate (FePO4) during the leaching process. This paper reports an extensive investigation of the effects of various factors, including the acid concentration, initial volume fraction of the oxidant, reaction temperature, solid-liquid ratio, and reaction time, on lithium leaching. Li+ reached a high leaching rate of 93.3% within 5 minutes even at a low concentration of sulphuric acid (H2SO4), and high-purity lithium carbonate (Li2CO3) was obtained through impurity removal and precipitation reactions. In addition, the leaching mechanism was analysed by both X-ray diffraction and X-ray photoelectron spectroscopy characterization. The results show that the obtained high lithium-ion (Li+) leaching efficiency and fast Li+ leaching time can be ascribed to the superior oxidizing properties of Na2S2O8 and the stability of the crystal structure of LiFePO4 during the oxidative leaching process. The adopted method has significant advantages in terms of safety, efficiency and environmental protection, which are conducive to the sustainable development of lithium batteries.

Conversion of Polyethylene to High-Yield Fuel Oil at Low Temperatures and Atmospheric Initial Pressure.

The transformation of waste plastics into fuels via energy-efficient and low-cost pyrolysis could incentivize better waste plastic management. Here, we report pressure-induced phase transitions in polyethylene, which continue to heat up without additional heat sources, prompting the thermal cracking of plastics into premium fuel products. When the nitrogen initial pressure is increased from 2 to 21 bar, a monotonically increasing peak temperature is observed (from 428.1 °C to 476.7 °C). At 21 bar pressure under different atmosphere conditions, the temperature change driven by high-pressure helium is lower than that driven by nitrogen or argon, indicating that phase transition is related to the interaction between long-chain hydrocarbons and intercalated high-pressure medium layers. In view of the high cost of high-pressure inert gases, the promotion or inhibition effect of low-boiling hydrocarbons (transitioning into the gaseous state with increasing temperature) on phase transition is explored, and a series of light components are used as phase transition initiators to replace high-pressure inert gases to experiment. The reason that the quantitative conversion of polyethylene to high-quality fuel products is realized through the addition of 1-hexene at a set temperature of 340 °C and the initial atmospheric pressure. This discovery provides a method for recycling plastics by low energy pyrolysis. In addition, we envisage recovering some of the light components after plastic pyrolysis as phase change initiators for the next batch of the process. This method is able to reduce the cost of light hydrocarbons or high-pressure gas insertion, reduce heat input, and improve material and energy utilization.

Thermochemistry of Sulfur-Based Vulcanization and of Devulcanized and Recycled Natural Rubber Compounds.

The vulcanization of rubber compounds is an exothermal process. A carbon black-filled and natural rubber-based (NR) formulation was mixed with different levels of sulfur (0.5, 1.0, 2.0, 4.0 and 6.0 phr) and studied with differential scanning calorimetry (DSC) for the determination of the vulcanization enthalpy. It was found that the vulcanization enthalpy is dependent on the amount of sulfur present in the compound and the vulcanization heat released was -18.4 kJ/mol S if referred to the entire rubber compound formulation or -46.0 kJ/mol S if the heat released is referred only to the NR present in the compound. The activation energy for the vulcanization of the rubber compounds was also determined by a DSC study at 49 kJ/mol and found to be quite independent from the sulfur content of the compounds under study. A simplified thermochemical model is proposed to explain the main reactions occurring during the vulcanization. The model correctly predicts that the vulcanization is an exothermal process although it gives an overestimation of the vulcanization enthalpy (which is larger for the EV vulcanization package and smaller for the conventional vulcanization system). If the devulcanization is conducted mechanochemically in order to break selectively the sulfur-based crosslinks, then the natural rubber compounds recovered from used tires can be re-vulcanized again and the exothermicity of such process can be measured satisfactorily with DSC analysis. This paper not only proposes a simplified mechanism of vulcanization and devulcanization but also proposes an analytical method to check the devulcanization status of the recycled rubber compound in order to distinguish truly devulcanized rubber from reclaimed rubber.

Global material flow analysis of end-of-life of lithium nickel manganese cobalt oxide batteries from battery electric vehicles.

The global market for battery electric vehicles (BEVs) is continuously increasing which results in higher material demand for the production of Li-ion batteries (LIBs). Therefore, the end of life (EOL) of batteries must be handled properly through reusing or recycling to minimize the supply chain issues in future LIBs. This study analyses the global distribution of EOL lithium nickel manganese cobalt (NMC) oxide batteries from BEVs. The Stanford estimation model is used, assuming that the lifespan of NMC batteries follows a Weibull distribution. The global sales data of NMC batteries from 2009 to 2018 were collected and the sales data from 2019 to 2030 were estimated based on historical trends and BEV development plans in the top 10 countries for BEV sales. The result shows a view of EOL NMC batteries worldwide. In 2038, China, South Korea and the United States (US) will be the three leading countries in the recovery of NMC battery materials. An overall global flow of NMC battery materials (aluminium, copper, manganese, steel, lithium and graphite/carbon) was also predicted in this research. This study estimated the waste potential of NMC battery materials specifically in the top 10 countries and also in other countries. Finally, the economic value estimation results for recovered materials indicated that copper, aluminium and manganese will have cumulative economic values of 7.9, 4.4 and 3.9 billion US dollars in 2038, respectively. As this study considers the different specific energy of NMC batteries in the coming years due to technological advancement, the findings can provide a more realistic insight into the future demand for NMC battery materials. This study reveals that a high number of EOL NMC batteries will be accumulated in 2038 in several countries. Therefore, large-scale recycling infrastructures should be set up to improve the efficiency of the recovery of battery materials.

Effectively remove printing ink from plastic surface over quaternary ammonium-modified waste cooking oil.

The printing ink on the plastic surface will greatly reduce the quality of recycled plastic products. In this work, quaternary ammonium-modified waste cooking oil (WCOEQ) was fabricated using waste cooking oil, epichlorohydrin, and trimethylamine aqueous solution as raw materials, through ring-opening esterification and quaternary amination reaction. The synthesis conditions of WCOEQ were optimised, and the structure and properties of WCOEQ were characterised by Fourier transform infrared spectroscopy, zeta potential, and 1H NMR. Furthermore, WCOEQ had excellent emulsifying performance, low kraft point, low critical micelle concentration value, good foaming, and stability, which could effectively reduce the surface tension of water, showing application potential in the field of plastic deinking. Importantly, compared with the waste cooking oil without deinking effect, the WCOEQ had an excellent deinking performance on the ink on the plastic surface, and the deinking efficiency could be improved by increasing the concentration of the deinking agent, the deinking temperature, and prolonging the pre-soaking and stirring time. The results of atomic force microscope, energy-dispersive spectroscopy, optical photos, and Leica microscope showed that the roughness changed significantly and the ink molecules were gradually peeling off. This work highlighted the potential of quaternary ammonium-modified waste cooking oil for excellent removal of printing inks on the plastic surface.

Example of removing printing ink from plastic surface using quaternary ammonium-modified waste cooking oil.

The printing ink on the plastic surface greatly reduces the quality of recycled plastic products. In this work, quaternary ammonium-modified waste cooking oil (WCOQE) was fabricated, using waste cooking oil, epichlorohydrin and trimethylamine aqueous solution as raw materials, by ring-opening esterification and quaternary amination reaction. The synthesis conditions of WCOQE were optimized, and the structure and properties of WCOQE were characterized by FTIR, zeta potential and 1H NMR. Furthermore, WCOQE had excellent emulsifying performance, low kraft point, low CMC value, good foaming and stability, which could effectively reduce the surface tension of water, showing application potential in the field of plastic deinking. Importantly, compared with the waste cooking oil without deinking effect, the WCOQE had an excellent deinking performance on the ink on plastic surface, and the deinking efficiency could be improved by increasing the concentration of deinking agent, the deinking temperature, and prolonging the pre-soaking and stirring time. The results of AFM, EDS, optical photos and Leica microscope showed that the roughness changed significantly, and the ink molecules were gradually peeling off. This work highlighted the excellent potential of quaternary ammonium-modified waste cooking oil for the removal of printing inks on the plastic surface.

Smoke filtration performances of membranes produced from commercial PVA and recycled PET by electrospinning method and ANN modeling.

Plastic waste and air pollution are becoming a great concern due to their adverse effect on human health and the environment. There is increasing number of evidence showing that recycling plastic and filtering harmful air pollutants are one of the most effective and promising way to eliminate their hazard on the environment. In this purpose, we developed eco-friendly filtration materials from recycled PET by electrospinning method to be used in air filtration and compared them with conventional PVA membranes. Filtration efficiency of prepared membranes were tested homemade membrane system using cigarette smoke source. Characterization results and smoke filtration performance of recycled PET and PVA membranes before and after smoke filtration were examined. The results demonstrated that the removal efficiencies of PVA-5 wt.%, PVA-10 wt.%, and PVA-15 wt.% were 4.11%, 11.32%, and 12.14%, respectively. A similar trend was also observed in recycled PET-5 wt.%, PET-10 wt.%, and PET-15 wt.% membranes with 4.32%, 10.79%, and 11.68% of filtration efficiency, respectively. Based on this result, using recycled PET can be an alternative way to produce a higher value product compared to traditional polymer membranes used commercially. This result is also supported by the neural network model of this study.

Upcycling face mask wastes generated during COVID-19 into value-added engineering materials: A review.

Billions of disposable face masks (i.e., single-use masks) are used and discarded worldwide monthly due to the COVID-19 outbreak. The immethodical disposal of these polymer-based wastes containing non-biodegradable constituents (e.g., polypropylene) has provoked marked and severe damage to the ecosystem. Meanwhile, their ever-growing usage significantly strains the present-day waste management measures such as landfilling and incineration, resulting in large quantities of used face-covering masks landing in the environment as importunate contaminants. Hence, alternative waste management strategies are crucially demanded to decrease the negative impacts of face mask contamination. In this venue, developing high-yield, effective, and green routes toward recycling or upcycling face mask wastes (FMWs) into value-added materials is of great importance. While existing recycling processes assist the traditional waste management, they typically end up in materials with downgraded physicochemical, structural, mechanical, and thermal characteristics with reduced values. Therefore, pursuing potential economic upcycling processes would be more beneficial than waste disposal and/or recycling processes. This paper reviews recent advances in the FMWs upcycling methods. In particular, we focus on producing value-added materials via various waste conversion methods, including carbonization (i.e., extreme pyrolysis), pyrolysis (i.e., rapid carbonization), catalytic conversion, chemical treatment, and mechanical reprocessing. Generally, the upcycling methods are promising, firming the vital role of managing FMWs' fate and shedding light on the road of state-of-the-art materials design and synthesis.

Sulfuric acid leaching of ball-milling activated FePO4 residue after lithium extraction from spent lithium iron phosphate cathode powder.

A mechanical-chemical process is proposed to recover the iron phosphate residue(IPR)of spent lithium iron phosphate(LFP)after lithium extraction. In this process, the IPR was pretreated by ball-milling and leached with the sulfuric acid solution. The results showed that, under the optimized ball-milling conditions (a mass ratio of the stainless-steel-ball to material to water of 2:1:2.5, a milling time of 20 min), the maximum particle size of IPR decreased from 34.265 um to 13.102 um, the specific surface increased from 11.41 m2/g to 13.74 m2/g, and the cell volume distortion rate could reach 0.331 %. Under the optimized leaching conditions (a temperature of 333 K, a concentrated acid-to-material ratio of 0.46 mL/g, a liquid-to-solid ratio of 5:1 mL/g, and a stirring speed of 600 rpm), the leaching efficiency of iron phosphate could reach 98 %. The kinetic study indicated that the leaching was controlled by diffusion and chemical reaction with the apparent activation energy of 29 kJ/mol. The dissolution-precipitation phase transition of IPR was also found at high temperatures. This study illustrates that such a mechanical-chemical process is an effective way to improve the leaching efficiency of IPR with a lower sulfuric acid dosage, which has great potential in industrial applications.

Olive-tree polyphenols and urban mining. A greener alternative for the recovery of valuable metals from scrap printed circuit boards.

Recycling printed circuit boards (PCBs) is becoming a source of precious metals and an alternative to conventional mining. This phenomenon is now known as "urban mining." In this work, a polyphenols-rich plant extract has been obtained from olive-tree leaves, and its ability to contribute to reducing four metals, namely, Ag, Cu, Cr, and Sn, that are present in scrap PCBs has been studied. Three reductants (NaBH4, Fe°, and the olive-tree leaves extract) have been used to recover these valuable metals. An attempt has been made to minimize the concentration of the first two, replacing them with a natural, cheaper, and less toxic reductant. To achieve this goal, a computer-assisted factorial, composed, centered, orthogonal, and rotatable statistical design of experiments (FCCORD) has been used to build the experimental matrix to be carried out in the laboratory and, next, for the statistical treatment of the results. The results show that it is possible to achieve only a partial recovery of the four metals (silver, copper, chromium, and tin) from PCBs leachates by using sodium borohydride, iron, and the extract separately. In other words, none of these three reductants alone can completely remove any of the four metals in the leachate. Nevertheless, using the statistical design of experiments, the total recovery of the four metals has been achieved by combining the three reductants in the appropriate concentrations. Hence, polyphenols-rich plant extracts in general and olive-tree leaves extract in particular can be regarded as promising coadjuvants in the rising field of urban mining.

Flotation de-inking for recycling paper: contrasting the effects of three mineral oil-free offset printing inks on its efficiency.

Paper for recycling has become a promising raw material for the pulp and paper industry due to its low cost and because it is conducive to sustainable development. Unfortunately, recycled paper contains a high volume of printed paper that is difficult to deink, which restricts its applications. Flotation deinking plays an essential role in the product quality and process cost of wastepaper recycling. This study was performed to evaluate the deinkability of environmentally friendly offset inks by flotation deinking. For this purpose, three mineral oil free series of four-color inks, namely, hybrid light emitting diode ultraviolet (LED-UV), LED-UV, and vegetable oil-based inks, were printed on white lightweight coated papers under laboratory conditions. The deinking methodology involves repulping, deinking agent treatment, flotation, hand sheet making, and evaluation of the produced hand sheets. The obtained results indicated that the hybrid LED-UV prints had the best deinkability. After flotation deinking, the deinking efficiency and the whiteness of the hybrid LED-UV ink increased by 58.1% and 47.6%, respectively. LED-UV ink had a 46.9% increase in the deinking efficiency and a 37.0% increase in the whiteness of the hand sheet. The deinking efficiency of the vegetable oil-based ink was the lowest, at 42.1%, and the whiteness of the hand sheet increased only by 23.8%. The particle size distribution analysis demonstrated that the hybrid LED-UV four-color ink exhibited a larger value of the average particle size than the two other. Scanning electron microscopy revealed that the hybrid LED-UV ink particles on the surface of the fibers were the least abundant after deinking. The physical strength properties of the hand sheets, including tensile index, folding resistance, and interlayer bonding strength of the hybrid LED-UV, LED-UV inks, and vegetable oil-based inks, increased.